TiVo Community Forum banner
21 - 27 of 27 Posts

·
Registered
Joined
·
106 Posts
Discussion Starter · #21 ·
give me a second. i just moved my cable to the #3 port on my router. It was in the #4/dmz port. So I rebooted my tivo from hyperterminal. I still only see 1 light on my adapter. also, on my router, I only see indication lights for ports 1 and 2, which are my computer and vonage router. The lights for #3 aren't lit up. I have the router firewall off. I'll try the ifconfig -a and report back
 

·
Registered
Joined
·
106 Posts
Discussion Starter · #22 ·
Doing what rbautch mentioned above gets me this:

bash-2.02# sh /enhancements/net-launch.sh
Please enter a static IP address for your Tivo: 192.168.1.103
Please enter the IP address of your router: 192.168.1.1
/enhancements/net-launch.sh: /enhancements/ipaddress_flag: Read-only file system

couldn't read file "netconfig.tcl": no such file or directory

Doing what you suggested gets me this:


bash-2.02# ifconfig -a
lo Link encap:Local Loopback
inet addr:127.0.0.1 Bcast:0.0.0.0 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:38 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:2766 dropped:38 overruns:0 carrier:0 coll:0
 

·
Registered
Joined
·
991 Posts
KrazyKevin said:
Doing what rbautch mentioned above gets me this:...
The ifconfig output indicates the device isn't recognized, so the right driver probably isn't loaded. The "Read-only file system" and "couldn't read file" messages indicate the 'net-launch.sh' script you are running problem didn't do what it was supposed to do. rbautch is your man for that.
 

·
Registered
Joined
·
106 Posts
Discussion Starter · #24 ·
Thanks alot. Maybe he'll see all this in the morning. Thanks again.

rbautch, I get this message:

bash-2.02# sh /enhancements/net-launch.sh
Please enter a static IP address for your Tivo: 192.168.1.103
Please enter the IP address of your router: 192.168.1.1
/enhancements/net-launch.sh: /enhancements/ipaddress_flag: Read-only file system

couldn't read file "netconfig.tcl": no such file or directory

But, I've went to that directory and the file is there. :(
I'm giving up for tonight. Hope to start back later tomorrow. Thanks all.


Kevin
 

·
Princess Anti-Santa
Joined
·
11,764 Posts
I had problems connecting with the 200M adapter as well. The Netgear FA120 works much more reliably.
 

·
Registered
Joined
·
1 Posts
Samsung 4040 w/dtv 6.2 zipped w no errors on the install, it did it's self reboot. usb activated, poked around a bit and did restart from menu. pluged in a netgear ea101 usb 1.1 6mb. on boot the adapter's usb power and link leds lit up. I tried to telnet, ping and it didn't go. :confused: made a serial, hypertermed it and noticed the error "usb.c: USB device 2 (vend/prod number/number) is not claimed by any active driver. dtvo booted all the way. went to my pc and did a portscan on my subnet with no response. Tried running eathereal to see if i could "see" any activity on mac layer incase it was on another subnet and still a no show. tried a dlink 1somthin & 266w and still got the error: usb.c: USB device 2 (vend/prod number/number) is not claimed by any active driver. But the vend/product number was diff per adapter. So I shrugged it off for while. Purchased a Linksys usb200m 2.0 w/o the v2 sticker on the box. Hypertermed ran Enhancement script installed 2.0 drivers and the whole deal. rebooted, plugged in the 200m and got the usb.c: USB device 2 (vend/prod number/number) is not claimed by any active driver. power and link lights are on, but no activity. :mad:
 

·
Registered
Joined
·
117 Posts
KrazyKevin said:
I got the zipper installed and used the serial cable to run the enhancement script. I thought I read somewhere that after the enhancement portion of the zipper, the new usb 2 drivers would allow the ver 2 adapter to work. I still only get the middle green light of the adapter to light up. Has anyone got a version 2 USB200M to work after the zipper?
How do you run the enhancement script via a serial cable?
I have everything installed on an HR10-250 but since I have a USB200M I cannot run the enhancement script
 
21 - 27 of 27 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top