[star-gazer-1247]

I tried all the codes listed in the TiVo button > Settings & Messages > Remote, CableCARD, & Devces > Remote Control Setup > Set TV Power, Volume, and Mute > RCA:
0368, 0371, 0004, 0001, 0006, 0011, 0029, 0030, 0057, 0083, 0133, 0145, 0161, 0163, 0171, 0231, 0232

None of these codes works for my 2015 RCA TV remote.
I did an internet search and found codes 0106 and 2210.
These also did not work.

Does anyone know the correct remote control 4 digit code for the RCA TV that will work with my TiVo Bolt remote control, so I can control the RCA TV power, volume, mute and input keys using my TiVo Bolt remote?

Thanks

 

[pl1]

Does anyone know the correct remote control 4 digit code for the RCA TV that will work with my TiVo Bolt remote control, so I can control the RCA TV power, volume, mute and input keys using my TiVo Bolt remote? Thanks

I don't, but, there is a way to scroll through every code that exists. (This page also shows how to search for Input & A/V) Search for a code to control TV power and volume
1. Cover the end of the TiVo remote control with your hand.
2. Hold down the TiVo and TV Power buttons simultaneously until the red (or amber) light on the remote control remains on.
3. Remove your hand from the end of the TiVo remote control.
4. Enter code 0999.
5. After you enter the code, the red (or amber) light will flash three times and then remain on.
6. Press Channel Up once every two seconds. This will test hundreds of codes, one by one. Do not go any faster than this or you may skip over a code that works.

Remote Control Programming Reminders:

• If you press Channel Up and your TV turns off, press Enter to select the code. Press the TV Power button to test the code. If your TV turns on, you have successfully programmed the remote
• If you cycle through all the codes, the red LED will go off, indicating that you have tried all the codes. If this happens, or if you selected a code but the TV does not respond to the test, try again to make sure you did not skip over your code by going too fast.
• If you can't find a code that works, your current remote may not be pre-programmed with the code for your TV. If you have a Premiere XL, TiVo HD XL, or Series3 HD DVR, you have a learning remote that can easily be "taught" to control your TV. For instructions, go to How to Use the Learning Feature of TiVo Learning Remotes.

 

[Edmund]

Try the codes for LG or Vizio.

 

[okay_see]

Try the codes for LG or Vizio.

ugh, not working. the search goes on

 

[okay_see]

I don't, but, there is a way to scroll through every code that exists. (This page also shows how to search for Input & A/V) Search for a code to control TV power and volume
1. Cover the end of the TiVo remote control with your hand.
2. Hold down the TiVo and TV Power buttons simultaneously until the red (or amber) light on the remote control remains on.
3. Remove your hand from the end of the TiVo remote control.
4. Enter code 0999.
5. After you enter the code, the red (or amber) light will flash three times and then remain on.
6. Press Channel Up once every two seconds. This will test hundreds of codes, one by one. Do not go any faster than this or you may skip over a code that works.

Remote Control Programming Reminders:

• If you press Channel Up and your TV turns off, press Enter to select the code. Press the TV Power button to test the code. If your TV turns on, you have successfully programmed the remote
• If you cycle through all the codes, the red LED will go off, indicating that you have tried all the codes. If this happens, or if you selected a code but the TV does not respond to the test, try again to make sure you did not skip over your code by going too fast.
• If you can't find a code that works, your current remote may not be pre-programmed with the code for your TV. If you have a Premiere XL, TiVo HD XL, or Series3 HD DVR, you have a learning remote that can easily be "taught" to control your TV. For instructions, go to How to Use the Learning Feature of TiVo Learning Remotes.

This finally worked with RCA. It literally took close to 5 minutes or more of scrolling through codes.