TiVo Community Forum banner
1 - 20 of 35 Posts

·
Registered
Joined
·
22 Posts
Discussion Starter · #1 ·
My HR10-250 setup has worked flawlessly for a year now. I have an OTA antenna on the roof next to the dish. The OTA signal comes down into my living room in one cable that carries both satellite and OTA via diplexing. I have other cables that carry the satellite signal exclusively and feed the Sat Input 2 on the HR10-250 and a couple other SD receivers in other rooms.

All of a sudden, the past few days, I am having all sorts of problems with the HR10-250 Sat Input 1 (the one that is diplexed with the OTA signal). On most transponders, I don't get a signal at all on Sat Input 1, even though Sat Input 2 is over 90 (some transponders are at a signal strength around 60). I'm also experience weird inconsistency with my OTA signals as well. I've checked all of my connections in the house, but I haven't yet gone up to the roof to check those connections. Any ideas or help would be appreciated.

Thanks and happy holidays!

MJC
 

·
Registered
Joined
·
2 Posts
McTivo said:
My HR10-250 setup has worked flawlessly for a year now. I have an OTA antenna on the roof next to the dish. The OTA signal comes down into my living room in one cable that carries both satellite and OTA via diplexing. I have other cables that carry the satellite signal exclusively and feed the Sat Input 2 on the HR10-250 and a couple other SD receivers in other rooms.

All of a sudden, the past few days, I am having all sorts of problems with the HR10-250 Sat Input 1 (the one that is diplexed with the OTA signal). On most transponders, I don't get a signal at all on Sat Input 1, even though Sat Input 2 is over 90 (some transponders are at a signal strength around 60). I'm also experience weird inconsistency with my OTA signals as well. I've checked all of my connections in the house, but I haven't yet gone up to the roof to check those connections. Any ideas or help would be appreciated.

Thanks and happy holidays!

MJC
I have almost the same setup and I just started having the same problem, but its only affecting my OTA channels, and only my Tivo box (perfect OTA signal on a regular directv HD box that I also have hooked up).

Good to know someone else is having the same problem I guess.
 

·
Registered
Joined
·
22 Posts
Discussion Starter · #4 ·
JimSpence said:
You need to check the ouside connections for corrosion. It could also be the outside diplexer.
Thanks. I haven't had a chacne to get up on the roof yet to take a look, however now Tuner 1 is working perfectly. If it were corrosion with the outside connections or the outside diplexer, would it make sense that the problem comes and goes? Or does that sound more like it might be a hardware failure inside the box?

Thanks again for the help.

MJC
 

·
Registered
Joined
·
84 Posts
Bad diplexers are all too common. The connections can be fine but the diplexer might not be doing its job and be cutting off the Sat signal at too high a frequency.
 

·
Registered
Joined
·
120 Posts
If the problem happens again, swap the tuner 1 and 2 connections at the HR10. If the problem moves to tuner 2, then it's upstream of the DVR. Most likely an intermittent connection, or flakey diplexer.

If the problem stays on tuner 1, it's the HR10. It could be the internal splitter or tuner 1 itself; I've had one box with a dead tuner. (dead out of the box... great quality control from DTV)
 

·
HD evangelist
Joined
·
2,517 Posts
It may also be simply a case of the logic controlling the multiswitch in the LNBF becoming scrambled. A reboot and a signal check should eliminate that possiblility. Since that's easy, I would do that first.
 

·
Registered
Joined
·
22 Posts
Discussion Starter · #9 ·
OK...

If you look back at my first post in this thread, you'll get some background on my problem. Over the past six weeks, I've replaced the diplexer on the roof twice. Each time, the problem goes away for 2-3 weeks, then it reappears. Of course, it reappeared yesterday (the day before the Super Bowl).

What could be causing my diplexers to die after 2-3 weeks of use? I'll go to Radio Shack today and buy another replacement diplexer, but this will get old after awhile. I could call DTV for service, but the techs that came out and installed it over a year ago were so bad and incompetent that I don't think I want them to come back. On top of that, I'm moving this summer, so I only have a few more months of use for this set-up anyway.

Any ideas are appreciated!

Thanks,
McTivo
 

·
Bring on the HD
Joined
·
96 Posts
I'm considering using the same setup. I want to put an indoor OTA antenna (Zenith Silver Sensor) in my attic, and run RG6 from the attic down the side of the house and into the living room where my 5x8 multiswitch and HR10 reside.

My problem is I already have four lines coming in through the wall (from the dish) and another going out (from the multiswitch to an upstairs TV). If I get the drill out to run another line in from the antenna I'm not sure my marriage will last. So I want to diplex the antenna line onto one of the four lines from the dish.

Some questions --
Have people had success with this setup?
What type of diplexer should I use (frequency ratings)?
When I separate the lines again on the other side, do I run the antenna signal directly into the HR10, or into the multiswitch first? I only have one TV that needs the OTA signal.


Thanks!
 

·
Registered
Joined
·
462 Posts
McTivo said:
OK...

If you look back at my first post in this thread, you'll get some background on my problem. Over the past six weeks, I've replaced the diplexer on the roof twice. Each time, the problem goes away for 2-3 weeks, then it reappears. Of course, it reappeared yesterday (the day before the Super Bowl).

What could be causing my diplexers to die after 2-3 weeks of use? I'll go to Radio Shack today and buy another replacement diplexer, but this will get old after awhile. I could call DTV for service, but the techs that came out and installed it over a year ago were so bad and incompetent that I don't think I want them to come back. On top of that, I'm moving this summer, so I only have a few more months of use for this set-up anyway.

Any ideas are appreciated!

Thanks,
McTivo
Try buying a different brand of diplexer. If you want to drive out to Bartlett, I've got a couple of brand new Channel Master diplexers I'd give you. If you want to pay about $10 each for them you can go to Tristate Electronic in Mt. Prospect any buy the Channel Master brand of diplexers there.
 

·
Registered
Joined
·
62 Posts
pudge44 said:
I'm considering using the same setup. I want to put an indoor OTA antenna (Zenith Silver Sensor) in my attic, and run RG6 from the attic down the side of the house and into the living room where my 5x8 multiswitch and HR10 reside.

My problem is I already have four lines coming in through the wall (from the dish) and another going out (from the multiswitch to an upstairs TV). If I get the drill out to run another line in from the antenna I'm not sure my marriage will last. So I want to diplex the antenna line onto one of the four lines from the dish.

Some questions --
Have people had success with this setup?
What type of diplexer should I use (frequency ratings)?
When I separate the lines again on the other side, do I run the antenna signal directly into the HR10, or into the multiswitch first? I only have one TV that needs the OTA signal.

Thanks!
If you only need OTA on one TV and you're planning on using an indoor antenna, why do you feel the need to diplex at all? Why not put the Silver Sensor where the TV is that needs the OTA signal and run the cable directly into the HR10-250's antenna input?

If it's because you can't get reception with the SS this way and you feel that placing it in your attic will work better than you'll need a diplexer that passes power on one leg like this one.....separate the two signals with another diplexer before going into the 5x8.
 

·
Registered
Joined
·
2 Posts
Mr. Bill said:
I would not buy RatShack diplexers.

I have Eagle Aspen from Solid Signal and they are 5 bucks each. I diplex OTA to 4 different locations, inc. an HR10, with no issues at all.
Ratshack wanted over $23.00 each for diplexers in my area. I didn't find out until she rang them up (because I never expected them to be so much), you can imagine I told them they could keep them. Currently using a very cheap indoor antenna and the reception shows it. This is on a HD- HTL that was moved to the bedroom when the HR10-250 arrived. Where would be a good place to get the Eagle Aspens? Is Solid Signal a web company?
 

·
Bring on the HD
Joined
·
96 Posts
Vin said:
If you only need OTA on one TV and you're planning on using an indoor antenna, why do you feel the need to diplex at all? Why not put the Silver Sensor where the TV is that needs the OTA signal and run the cable directly into the HR10-250's antenna input?

If it's because you can't get reception with the SS this way and you feel that placing it in your attic will work better than you'll need a diplexer that passes power on one leg like this one.....separate the two signals with another diplexer before going into the 5x8.
Yeah, I want to put it up in the attic to get better reception. I do all right with it sitting on top of th TV, but my TV's not in an entertainment center so it looks pretty ungainly up there. Doesn't do a whole lot sitting on the floor behind the TV. Up in my attic, there's a vent that's aimed right at the towers. I'm thinking I might do real well up there.
 

·
Registered
Joined
·
22 Posts
Discussion Starter · #16 ·
Mr. Bill said:
I would not buy RatShack diplexers.

I have Eagle Aspen from Solid Signal and they are 5 bucks each. I diplex OTA to 4 different locations, inc. an HR10, with no issues at all.
What is the difference between PowerPass diplexers and regular diplexers? The diplexers I am currently using are the RCA D920s. 14 months ago, when the D* installers installed a Winegard antenna on the roof, they said that it drew power from the coax and need the "PowerPass" diplexers, so they installed the Eagle Aspen D-2100LX diplexers. Well, that antenna was not the right antenna for me, so I picked up an old-fashioned antenna from Radio Shack and swapped it with the Winegard. The Radio Shack antenna works great, but after I first hooked it up I noticed that the HDTivo was hissing. That's when I switched from the Eagle Aspen diplixers (the PowerPass ones) to the RCA diplexers (non-PowerPass). The hissing went away and everything worked great for a year.

I still have the Eagle Aspen diplexers, but I fear that I don't need the PowerPass capabilities that this model offers. Am I right? Are there any other brands of diplexers that aren't PowerPass? What about the Channel Master diplexers SpankyInChicago mentinoed?

Thanks for everyone's help!

McTivo
 

·
Registered
Joined
·
76 Posts
Sorry, I do not know the difference about the terms as you are using them.

I do know that there is another type of diplexer called dual-port passive. They are used only at the top end of an installation (near the dish) when you have an antenna that is drawing power through the same coax as the dish uses. They are built to handle the voltage switching back and forth from 13 volts to 17 volts that happens between a satellite receiver and the LNB as it changes to different LNBs/sats when you are changing channels.

If you have the dish/OTA typical setup, with an antenna that is non-powered or is powered via it's own separate connection to a power outlet, then you want a passive diplexer. SolidSignal.com is a web retailer and a very good one. They are a sponsor over at AVS. Eagle Aspen is a very good manufacturer of splitters, diplexers, tone generators and multiswitches.

You want the Eagle Aspen Single Port Power Passive Diplexer, Manufacturer P/N: D-2100LX. 5 bucks.

Now, I see that you said you have that model, so maybe your antenna is powered off the dish's coax?? If it is, get the DO-2100LX. I don't know what else it could be.

Hope that helps. ;)

Update: You may want to give Solid Signal a call -- they have great phone info. Or, try the AVS 'HDTV Reception Hardware' forum. They deal with OTA integration issues you have and there is a member there, SolidSignal, who works at their HQ and often chimes in (as does Greywolf from upthread here).
 

·
Everyday is Saturday
Joined
·
6,232 Posts
So. I want to put an antenna in the attic. The Silver Sensor works great downstairs, but I don't want to look at it.

But I want two antenna inputs to the HDTIVO so I can record 2 OTA shows at the same time.

I guess no one recommends running the antenna feed into the multiswitch (also in the attic)?

If not, do I put a diplexer on each of two feeds coming out of the multiswitch, then hook a feed and antenna lead to each (split antenna with a splitter) and then two more diplexers on the TV end?

If I decide to keep the Silver Sensor DOWNstairs, can I just put a splitter on it and run a feed into each antenna input?
 

·
Bring on the HD
Joined
·
96 Posts
Philly Bill said:
So. I want to put an antenna in the attic. The Silver Sensor works great downstairs, but I don't want to look at it.

But I want two antenna inputs to the HDTIVO so I can record 2 OTA shows at the same time.

I guess no one recommends running the antenna feed into the multiswitch (also in the attic)?

If not, do I put a diplexer on each of two feeds coming out of the multiswitch, then hook a feed and antenna lead to each (split antenna with a splitter) and then two more diplexers on the TV end?

If I decide to keep the Silver Sensor DOWNstairs, can I just put a splitter on it and run a feed into each antenna input?
Phil, I'm pretty sure the HR10 has only one antenna input, and that it splits the OTA signal internally to allow dual tuner OTA recording.
 

·
Registered
Joined
·
462 Posts
McTivo said:
What is the difference between PowerPass diplexers and regular diplexers? The diplexers I am currently using are the RCA D920s. 14 months ago, when the D* installers installed a Winegard antenna on the roof, they said that it drew power from the coax and need the "PowerPass" diplexers, so they installed the Eagle Aspen D-2100LX diplexers. Well, that antenna was not the right antenna for me, so I picked up an old-fashioned antenna from Radio Shack and swapped it with the Winegard. The Radio Shack antenna works great, but after I first hooked it up I noticed that the HDTivo was hissing. That's when I switched from the Eagle Aspen diplixers (the PowerPass ones) to the RCA diplexers (non-PowerPass). The hissing went away and everything worked great for a year.

I still have the Eagle Aspen diplexers, but I fear that I don't need the PowerPass capabilities that this model offers. Am I right? Are there any other brands of diplexers that aren't PowerPass? What about the Channel Master diplexers SpankyInChicago mentinoed?

Thanks for everyone's help!

McTivo
The ChannelMasters pass DC power on the sat leg and block DC on the antenna leg. This should be what you need. Unless your antenna is powerd or has an amp, you need a DC block on the antenna leg.
 
1 - 20 of 35 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top