TiVo Community Forum banner
1 - 2 of 2 Posts

·
Registered
Joined
·
926 Posts
Discussion Starter · #1 ·
Just wondering if it's me that is having daily call problems today?

Connecting via a cachecard.
my rc.net is
Code:
#
#!/bin/sh
#

if /sbin/insmod -f /lib/modules/turbonet2.o macaddr=00:0B:AD:C5:E0:B3 debuglevel=0 ; then
        export DYNAMIC_NET_DEV=eth0
        /sbin/ifconfig eth0 192.168.1.200 netmask 255.255.255.0 mtu 1458 up
        # avoid annoying "route.tivo forgot to specify route netmask" error:
        /sbin/route.tivo add default gw 192.168.1.254 netmask 0.0.0.0
fi
route.tivo -n gives
Code:
/etc/rc.d # /sbin/route.tivo -n
route_info, afname=inet, options=37
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.1.0     0.0.0.0         255.255.255.0   U     32767  0        0 eth0
0.0.0.0         192.168.1.254   0.0.0.0         UG    0      0        0 eth0
In a recent working daily call log it goes
Code:
08/17:06:13:09: /tvbin/TClient:  Logging camid.
08/17:06:13:09: /tvbin/TClient:  CAM_ID not found.
08/17:06:13:09: /tvbin/TClient:  Ird Id.
08/17:06:13:09: /tvbin/TClient:  updateStatus: In Progress CL| 30 24
08/17:06:13:09: /tvbin/TClient:  SendDialupEvent 30 9 CL|30
08/17:06:13:09: /tvbin/TClient:  updateStatus: In Progress ST| 33 14
08/17:06:13:09: /tvbin/TClient:  SendDialupEvent 30 9 ST|33
08/17:06:13:09: /tvbin/TClient:  About to connect to 204.176.49.3:80
08/17:06:13:09: /tvbin/TClient:  Executing HTTP command: /tvbin/http_post /var/log/svclog http://204.176.49.3:80/tivo-service/mlog.cgi OFF OFF ON
08/17:06:13:10: /tvbin/TClient:  about to do TCD411 Call
But today it's saying
Code:
08/21:06:47:39: /tvbin/TClient: Logging camid.
08/21:06:47:39: /tvbin/TClient: CAM_ID not found.
08/21:06:47:39: /tvbin/TClient: Ird Id.
08/21:06:47:39: /tvbin/TClient: toneOrPulse = 0
08/21:06:47:39: /tvbin/TClient: dialPrefix = ,#090,
08/21:06:47:39: /tvbin/TClient: callWaitingPrefix == {}
08/21:06:47:39: /tvbin/TClient: phoneNumber = 08081050005
08/21:06:47:39: /tvbin/TClient: phoneAvailableDetection = 0
08/21:06:47:39: /tvbin/TClient: dialToneDetection = 0
08/21:06:47:39: /tvbin/TClient: Starting dial.expect with:
08/21:06:47:39: /tvbin/TClient: toneOrPulse = T
I can connect out OK from my tivo:
Code:
# /bin/ntpdate -b 158.152.1.76 158.43.128.33 204.176.49.40 204.176.49.41
21 Aug 17:12:28 ntpdate[427]: step time server 158.43.128.33 offset 1.941368 sec
nic_config_tivo confirms that I'm set to make the call over the network. A fresh pair of eyes may help spot the problem I hope! Ie where else does it decide whether to use the network or modem for the call?
 

·
Registered
Joined
·
926 Posts
Discussion Starter · #2 ·
Ah, it was just me :). Turns out I had two hdparm lines in my rc.sysinit.author lines which weren't backgrounded.

Quite wierd to diagnose but I got the hint from one of the few threads which contained the same message I was getting - "failed. Line unavailable".
 
1 - 2 of 2 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top